Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
system_tools:installing_cores_quartus [2019/11/29 00:39]
muaddib [Installing new Cores using Quartus II Programmer]
system_tools:installing_cores_quartus [2020/04/04 12:51] (current)
muaddib
Line 34: Line 34:
 {{:​settings-icon.png?​nolink&​48|}} {{:​settings-icon.png?​nolink&​48|}}
  
-{{:​warning-icon.png?​nolink&​24|}} **POWER OFF your Amiga / Vampire**, **__NEVER__** connect or disconnect the **USB-Blaster** while your Amiga / Vampire is powered on!+{{:​warning-icon.png?​nolink&​24|}} **POWER OFF your Amiga / Vampire**, ​and also **DISCONNECT** all devices that have their own power connection, such as Digital Video and Ethernet cables, to prevent power backfeed into the Vampire.  ​**__NEVER__** connect or disconnect the **USB-Blaster** while your Amiga / Vampire is powered on!
  
 Below is the full connection chain to use: Below is the full connection chain to use:
Line 41: Line 41:
  
 Afterwards, if your PC is turned on, the '​POWER'​ LED on the USB-Blaster should be '​red'​. Afterwards, if your PC is turned on, the '​POWER'​ LED on the USB-Blaster should be '​red'​.
 +
 +//Example connection if you have a Vampire accelerator board connected to a classic Amiga://
  
 {{:​usbblaster-003.jpg?​direct&​600|}} {{:​usbblaster-003.jpg?​direct&​600|}}
 +
 +//Example connection if you have a Vampire Standalone://​
 +
 +{{:​v4_jtag_coreupdate.jpg?​direct&​400|}}
 +
 +<callout type="​primary"​ icon="​true">​
 +Make sure that the JTAG cable is inserted into the correct header on the Vampire, and with the correct orientation. ​ The red stripe that is on one side of the JTAG cable must be aligned with Pin 1 of the JTAG header.
 +</​callout>​
  
 ---- ----
Line 66: Line 76:
     * On some Linux distributions,​ you might need to install old versions of some libraries, like ''​libpng12''​.     * On some Linux distributions,​ you might need to install old versions of some libraries, like ''​libpng12''​.
   - You might need to install the USB driver for the ''​USB-Blaster''​ by hand.   - You might need to install the USB driver for the ''​USB-Blaster''​ by hand.
-    * On Windows, open the **Device Manager** and ensure that the USB Driver ​for USB-Blaster is correctly installed. If it is **NOT** correctly installed, then select the .INF driver information file from the Quartus setup archive.+    * On Windows, open the **Device Manager** and ensure that the USB driver ​for USB-Blaster is correctly installed. If it is **NOT** correctly installed, then select the .INF driver information file from the Quartus setup archive.
  
 {{:​usbblaster-004.png?​direct&​400|}} {{:​usbblaster-004.png?​direct&​400|}}
Line 95: Line 105:
     * **__NEVER__** switch off the computer during a flash operation.     * **__NEVER__** switch off the computer during a flash operation.
     * Do **NOT** use your operating system during a flash operation.     * Do **NOT** use your operating system during a flash operation.
-  - **Power OFF** your Amiga / Vampire and wait at least __10 seconds__.+  - **Power OFF** your Amiga / Vampire, disconnect the USB-Blaster, ​and wait at least __10 seconds__.  Make sure that all devices that have their own power connection, such as Digital Video and Ethernet cables, are also **disconnected** during this time, to prevent power backfeed into the Vampire.
   - Finally, **Power ON** your Amiga / Vampire.   - Finally, **Power ON** your Amiga / Vampire.
  
Last modified: le 2019/11/29 00:39